Veröffentlichungshinweise

Ver. 1.18.01 (18 Dec 2024)

Added

  • Modbus protocol: if coefficient is active, gross and net weight, with the coefficient applied, are published

Fixed

  • CANOPEN: MODBUS communication through RS485 port returns several errors during data exchange

Ver. 1.18.00 (25 Nov 2024)

Added

  • Firmware version compliant with INMETRO regulation
  • Modbus protocol: address 0 supported for broadcast communication
  • Analog output: output current or voltage value configured by remote
  • RS485 serial port: continuous transmission YHL protocol available

Ver. 1.17.00 (24 Oct 2023)

Fixed

  • When a semi-automatic tare is active, gross weight temporary visualization, pressing Up arrow key, doesn't work

Ver. 1.16.05 (22 May 2023)

Fixed

  • Modified one of the voltage thresholds used by diagnostic functions, to avoid load cell error condition incorrect signalings

Ver. 1.16.04 (18 Apr 2023)

Fixed

  • The reset procedure was changed because after resetting the instrument to the factory defaults, the weight was not calculated correctly.

Ver. 1.16.03 (02 Dec 2022)

Fixed

  • Threshold for load cell error alarm modified, to avoid wrong signallings

Ver. 1.16.02 (17 Nov 2022)

Fixed

  • ASCII protocol: fixed semiautomatic zero and semiautomatic tare commands working

Ver. 1.16.01 (19 Jul 2022)

Internal changes without any impact on the user

Ver. 1.16.00 (26 Jan 2022)

Internal changes without any impact on the user

Ver. 1.15.02 (21 Oct 2020)

Fixed

  • Communication errors, in case of MODBUS reading if more than 10 registers are required

Ver. 1.15.00 (22 Sep 2020)

Added

  • Real calibration, command code 106: a new calibration point is added
  • Real calibration, checks executed when a new calibration point is defined:
    • Operation not executed if the sample weight is equal to 0
    • Operation not executed if the sample weight is used in one of the currently defined calibration points

Changed

  • Real calibration, command code 101 original functioning restored. It deletes all previously registered calibration points and add a new one

Ver. 1.14.16 (18 Jun 2020)

Changed:

  • Relay outputs maintained open during instrument startup

Ver. 1.14.13 (11 Jan 2020)

Internal changes without any impact on the user

Ver. 1.14.11 (29 Nov 2019)

Added

  • First firmware release compliant with Instrument Manager service software

Ver. 1.12.07 (03 Oct 2019)

Fixed

  • Analog output, 0-20 mA o 4-20 mA types: minimum output current value set to -0.5 mA, maximum output current value set to 22 mA
  • Analog output, 0-5 V 0 0-10 V types: minimum output voltage value set to -0.5 V, maximum output voltage value set to 10.2 V 

Ver. 1.12.06 (11 Oct 2018)

Fixed

  • Wrong syntax for transmiteed string, in case of CONTIN protocol, MOD TD mode active

Ver. 1.12.05 (29 May 2018)

Internal changes without any impact on the user

Ver. 1.12.03 (21 May 2015)

Fixed

  • If RIP, HDRIP or HDRIPN protocol enabled, peak weight transmitted, instead of the net weight, when peak function is active

Ver. 1.12.01 (17 Jul 2014)

Added

  • Specific menu for anti peak filter setup

Ver. 1.11.02 (19 Jan 2012)

Fixed

  • Setpoint menu, Setp1 label changed in Set 01. The other setpoint labels has been changed in the same way

Ver. 1.11.00 (02 Dec 2011)

Added:

  • MODBUS-RTU: preset tare execution